V
ViktorHF
I got the Srttrail.txt Bluescreen Error on Winows 10 x64 Desktop(with GTP Drive)...
I recently purchased a software(VST plugin) which required registration with PACE iLOK Licence Manager. The installation of iLOK required restarting my PC, but has now sent my computer in a bluescreen loop: "Automatic Repair, Your PC did not start correctly..." After Startup repair not being able to repair my computer, it reffered me to a log file. In the logfile (C:\WINDOWS\System32\Logfiles\Srt\Srttrail.txt) I found the error codes 0x32 and 0x57 with the translated message “Unspecfied changes in the system configuration may have caused the problem”
I am now unable to boot my computer, even with all the WinRE startup alternatives such as enable safemode etc… I cant even force boot safemode with bcdedit /set {default} safeboot minimal. I do not have any system reset points even though I used one about 3 weeks ago. So, I installed Windows Installation Media on a flash drive and tried to repair the system with it, but not even that takes me past the Windows Recovery Environment.
After a while I got this new bluescreen message: “After multiple tries, the operating system on your PC failed to start, so it needs to be repaired. Error code: 0xc0000001.”
Note: Performing a clean install of windows is my absolute last option and I am willing to try whatever might work! I have already backed up the most important files to a USB using the cmd notepad.exe trick.(Hope I made myself clear that I can't access windows)
What I already have tried:
diskpart
select disk 0
select volume 8
assign letter=S
exit
cd /d S:\efi\microsoft\boot\
attrib bcd -s -h -r
ren bcd bcd.bak
bcdboot c:\windows /l en-us /s S: /f /all
Since I´m from Sweden I also tried the bcdboot command with the swedish sv-SE locale. Both cases-> "Boot files successfully created"
Scan Results & System Info FYI
(dir C:, list part, list volume, BcdEdit,CHKDSK)
Thankful for all the help I can get!!
Continue reading...
I recently purchased a software(VST plugin) which required registration with PACE iLOK Licence Manager. The installation of iLOK required restarting my PC, but has now sent my computer in a bluescreen loop: "Automatic Repair, Your PC did not start correctly..." After Startup repair not being able to repair my computer, it reffered me to a log file. In the logfile (C:\WINDOWS\System32\Logfiles\Srt\Srttrail.txt) I found the error codes 0x32 and 0x57 with the translated message “Unspecfied changes in the system configuration may have caused the problem”
I am now unable to boot my computer, even with all the WinRE startup alternatives such as enable safemode etc… I cant even force boot safemode with bcdedit /set {default} safeboot minimal. I do not have any system reset points even though I used one about 3 weeks ago. So, I installed Windows Installation Media on a flash drive and tried to repair the system with it, but not even that takes me past the Windows Recovery Environment.
After a while I got this new bluescreen message: “After multiple tries, the operating system on your PC failed to start, so it needs to be repaired. Error code: 0xc0000001.”
Note: Performing a clean install of windows is my absolute last option and I am willing to try whatever might work! I have already backed up the most important files to a USB using the cmd notepad.exe trick.(Hope I made myself clear that I can't access windows)
What I already have tried:
- Manually removing the PACE oem driver in cmd. (Did not help)
- sfc /scannow /offbootdir=c:\ /offwindir=c:\windows -> "Windows Resource Protection did not find any integrity violations
- chkdsk c: /f /r /x ->"Failed to transfer logged messages to the event log with status 6"
- I also tried turning off auto repair with bcdedit /set {default} recoveryenabled no, no luck.
- Resetting the CMOS battery-> “Error: CMOS Checksum error- Defaults Loaded”
- mkdir C:\Scratch DISM /Image:C:\ /ScratchDir:C:\Scratch /Cleanup-Image /Restorehealth -> "Restore operation completed succesfully" but to no good it seems.
- I tried repairing the EFI Bootloader (where “S:” is the assigned EFI volume):
diskpart
select disk 0
select volume 8
assign letter=S
exit
cd /d S:\efi\microsoft\boot\
attrib bcd -s -h -r
ren bcd bcd.bak
bcdboot c:\windows /l en-us /s S: /f /all
Since I´m from Sweden I also tried the bcdboot command with the swedish sv-SE locale. Both cases-> "Boot files successfully created"
- bootrec /scanos tells me "Total identified windows installations:0"
Scan Results & System Info FYI
(dir C:, list part, list volume, BcdEdit,CHKDSK)
Thankful for all the help I can get!!
Continue reading...